A section of TSUISO, Japanese car culture in English Find me a car
JDMVIP

Japan’s VIP-style luxury sedansby TSUISO

The build, step by step

How a Japanese VIP car is built

Japanese builders and magazines work in a set order. Choose the base car, the top grade of a big domestic sedan. Get the ride height down with coilovers or air suspension. Fit the largest deep-lip wheels that sit flush with the arches. Only then add the aero, because a kit on a car still at stock height and on stock wheels looks wrong. Paint, interior, lights and exhaust come last. To stay on the road in Japan the car must still pass shaken, the roadworthiness inspection, which sets a minimum ground clearance of 9 cm.

Minimum ground clearance
9 cm (Japan)
Front window tint
70% light or more
Air suspension kit
from ¥470,000
20-inch three-piece wheel
from ¥145,200 each

Checked 16 November 2026 against the sources at the foot of the page.

A dark green S170 Toyota Crown Majesta built by Honda Tosou at Osaka Auto Messe 2016, lowered close to flush on deep mesh wheels
An S170 Crown Majesta built by Honda Tosou, Osaka Auto Messe 2016: low, near-flush wheels, deep mesh rims. Photo: Tokumeigakarinoaoshima, CC BY-SA 4.0.

The order builders work in

The build, from base car to finished

  1. Choose the base car

    The top grade of a Japanese maker’s biggest sedan, for the interior as much as the body: a Celsior, Crown Majesta, Cima, Cedric or Gloria, or less often a Century or President. Several top grades had air or active suspension from the factory, such as the C-spec Celsior and the JHG50 President, which changes how you lower the car. The base cars, generation by generation.

  2. Get the ride height down

    The step builders call the most important. Shorter springs alone will not get a big sedan low enough, so the choice is dedicated coilovers or air suspension, and on some cars the arms hit the body or subframe and need modifying. Coilovers from a VIP-focused maker such as IDEAL start at ¥159,000 before tax; air suspension kits run from ¥470,000 before tax (Air Force) to ¥852,500 including tax (ACC Air Runner for a UCF3# Celsior). Air lets the car sit on the ground at a show and lift to drive; leaks are its weak point. In Japan a car with adjustable height is measured for shaken at the middle of its range.

  3. Fit the wheels

    As large and as deep-lipped as the car will take, often three-piece. The aim is tsura-ichi, the wheel and tyre flush with the outside of the arch, done with a low-offset wheel rather than spacers, which can crack or work loose. Negative camber helps tuck the top of the tyre under the arch; taken to extremes it is oni-kyan, and it wears tyres fast. A WORK Meister S1 three-piece in 20 inches costs ¥145,200 to ¥172,700 a wheel, including tax.

  4. Add the aero

    After the height and wheels are set. Most VIP kits are low lip spoilers and side skirts, many of them under-spoilers that fit below the stock bumper; a car whose side skirts reach the ground is said to have “landed”. A full kit for a late UCF30 Celsior is ¥484,000 including tax from Junction Produce; a single front bumper from Aimgain’s 純VIP line is ¥120,000 before tax. The aero makers and what they still make.

  5. Finish it

    Paint, interior, lights and exhaust. A full respray costs several hundred thousand yen for the outside alone and several million for a strip-down job. Inside, the fusa tassel on the mirror, curtains and reupholstery; outside, an exhaust to match the kit and lights that stay within the legal colours. Window film on the windscreen and front side windows must still pass 70% of light.

Costs

What the parts cost in Japan

Prices published by the makers and shops named, in yen, on the dates shown. Fitting, paint and freight are extra.

ItemExamplePrice in JapanSource
CoiloversIDEAL Truva, VIP-focused, 36-way damping¥159,000 to ¥169,000 before taxVIP STYLE magazine, 23 Mar 2026checked 16 Nov 2026
Coilover fittinggeneral guide¥30,000 to ¥50,000Style Wagon / Dress-up Navi, 9 Feb 2023checked 16 Nov 2026
Air suspension kitAir Force Basic, Celsior¥470,000 before taxAir Force Suspensionchecked 16 Nov 2026
Air suspension kitACC Air Runner, Celsior UCF3# 2WD¥852,500 including taxACCchecked 16 Nov 2026
Air management onlyT-Demand Pressure Management kit, 2-way / 4-way¥320,000 / ¥480,000 before taxVIP STYLE magazine, 23 Mar 2026checked 16 Nov 2026
Air suspension fittinggeneral guidefrom ¥70,000Style Wagon / Dress-up Navi, 9 Feb 2023checked 16 Nov 2026
WheelsWORK Meister S1 three-piece, 20 inch, per wheel¥145,200 to ¥172,700 including taxWORK 2026 cataloguechecked 16 Nov 2026
Aero, full kitJunction Produce, Celsior UCF30/31 late¥484,000 including taxJunction Produce web shopchecked 16 Nov 2026
Aero, front bumperAimgain 純VIP, Celsior UCF30/31 late¥120,000 before taxAimgainchecked 16 Nov 2026
Full resprayoutside only / full strip-downseveral hundred thousand yen / several million yenNorimono News, 7 Apr 2025checked 16 Nov 2026

Add the examples up and a coilover build, with wheels and a full aero kit, comes to roughly ¥1 million before fitting and paint, not counting the car; air suspension adds several hundred thousand yen more. That is our sum of the prices above, not a quote.

Japanese inspection (shaken)

The limits a road-legal VIP car is built to in Japan

RuleWhat it saysSource
Ground clearanceAt least 9 cm for a car modified to sit lower, and more between the axles: wheelbase × ½ × 0.04 + 4 cm, about 10 cm on a 3 m wheelbase. A car with adjustable height is measured at its neutral position, or midway between lowest and highest if it can hold any height; resin air dams and skirts are not counted.MLIT detailed standards, art. 163 (and 85)
Wheels and tyres sticking outNothing that turns may stick out past the arch in the zone from 30° in front of to 50° behind the axle. Since 2017 the tyre’s own sidewall lettering, protective band and ribs may stick out by less than 10 mm on a passenger car; the wheel itself may not.MLIT detailed standards, art. 178
Side slipThe steered wheels must not slip more than 5 mm per metre on the side-slip tester, which heavy toe or camber changes can fail.MLIT detailed standards, art. 169
Window tintThe windscreen and the driver’s and front passenger’s windows must pass at least 70% of visible light; rear side windows are outside this rule.MLIT detailed standards, art. 195
LightsHeadlights white, tail and brake lights red, no other red or amber lights to the rear apart from the required ones, and no flashing lights. From 1 August 2026 headlight checks measure the low beam everywhere.MLIT detailed standards, arts. 198, 206, 212, 218; Kinki Transport Bureau
Modification noticesJapanese press reported that from 1 October 2026 fitting unmodified aftermarket suspension parts to a passenger car with up to nine seats no longer needs a modification notice; check the current rule with the inspection office.Kuruma News, 31 Mar 2026

These are Japan’s rules. Your own country inspects the car again when it arrives, and its limits on ride height, wheels and lights are its own.

Buying one already built

What we check on a VIP car before anyone pays for it

A built car can be the cheapest way into the style, or the most expensive. This is what we look at in Japan before we tell you to buy.

Underneath

Scrapes, dents and cracks on the floor pan, sills, sump, exhaust and fuel tank; bent or torn mounts; fresh undercoating over damage. A car that has lived low shows it here first.

Air suspension

Whether it holds height overnight with the engine off, how long the compressor runs to lift it, the condition of the bags, lines and fittings, and whether the tank drains water. Ask for the brand and when it was fitted.

Coilovers or cut springs

The brand and model of the coilovers, leaking dampers, and springs that have been cut or are loose at full droop. Cut springs are a red flag for how the rest of the car was done.

Camber and tyres

Inner-edge tyre wear, adjustable arms and their condition, and the alignment sheet if there is one. Heavy negative camber wears tyres fast and can hide worn bushes.

Wheels and arches

Lips curbed or bent, tyres stretched onto wide rims, and arches rolled or pulled to clear them; check for cracked paint on the arch lip and rubbing marks on the liners.

Aero

FRP (fibreglass) kits crack and get repaired; look for filler, mismatched paint and broken mounting tabs, and ask which maker’s kit it is, because it decides whether a replacement part exists.

Body and paint

Full repaints, the original colour code on the plate, and rust at the rear arches, sills and spare-wheel well. A repair history (修復歴) flag on the listing means a structural part was repaired, not necessarily a major crash.

Interior and electrics

Aftermarket lighting, audio and screens are wired in by someone: check for tidy wiring, working switches and warning lights, and a battery that is not being drained.

Papers

Whether the modifications were registered (公認, kōnin) or the car only passes inspection with parts swapped back, and whether the stock parts come with the car. Your own country’s inspection will judge the car as it arrives.

See built and stock cars for sale today

A UCF30 Celsior on ACC’s On the Ground air suspension, raised and lowered (2 minutes). ACCtv (ACC, the air suspension maker) on YouTube.

Building one outside Japan?

The parts for 1990s VIP cars are made and sold in Japan, often in Japanese only, and many are now second-hand. Tell us the car and the look you want: we can find the base car, the parts, or both, and ship them together.

Tell us your build See the parts makers

Sources

  1. WEB CARTOP via carview (12 July 2025): base car, ride height first, coilovers and arm clearance
  2. WEB CARTOP (22 March 2023): aero before height and wheels looks mismatched
  3. WEB CARTOP (25 May 2017): tsura-ichi with low-offset wheels, not spacers
  4. CarMe: negative camber and tyre wear
  5. CarMe: air suspension, controllers and leaks
  6. WORK 2026 catalogue: Meister S1 three-piece prices
  7. MLIT, detailed safety standards, article 163: ground clearance for vehicles in use
  8. MLIT, detailed safety standards, article 085: ground clearance at new registration
  9. MLIT, detailed safety standards, article 178: wheels and tyres protruding
  10. MLIT, detailed safety standards, article 169: steering and side slip
  11. MLIT, detailed safety standards, article 195: window glass
  12. MLIT, detailed safety standards, article 198: headlights
  13. MLIT, detailed safety standards, article 218: other lights
  14. Norimono News (9 July 2017): only the tyre may protrude, from 22 June 2017
  15. Kinki Transport Bureau: low-beam headlight measurement from 1 August 2026
  16. MLIT leaflet: illegal modifications (exhaust, lights, windows)
  17. Wikimedia Commons: Crown Majesta S170 by Honda Tosou, Osaka Auto Messe 2016 (CC BY-SA 4.0)

追走 · TSUISO DESK

Tell us your build

The car (or the car you want), the look, the parts you have in mind, your budget and where it ships to. We reply with what is for sale in Japan and what it would take.

  • Freeno commitment
  • In Japanwe are on the ground here
  • ~1 minto fill in
  • Englishor Japanese
Add dates or a budget (optional)